A natural choice for you and your baby

See our Online special offer of 4 weeks pool hire for £310 Online Order Form

Joshua was my first baby, he was born an hour after I got into the pool, I had no need for extra pain relief (and I'm no brave lady) and we were able to watch him swim up to the surface and take his first breath of

air.

About Our Pools

Features that set the Primavera Birthing Pool apart from its competitors.

Packaged in two easy to transport boxes each measuring 51cm x 61cm x 63cm
Easy assembly and dismantling procedure.
1.5kw dedicated water heater designed to run off domestic 13 amp power supply.
Digital heat regulation thermostat that allows you and your partner to concentrate on the birth rather than the water temperature.
Lightweight insulated sidewalls for greater temperature retention.
Reinforced liner with optional disposable inner liner to ensure the highest standards of hygiene.
Cushioned upper edges and floor for greater comfort and easier manoeuvring into birthing positions.
Advanced water filtration system and water treatment procedures allowing up to 7 days' continual use
Secure, lockable thermal cover that keeps children or pets safe from harm, allows prolonged pool use and reduces condensation.
Easily cleaned filtration system with replaceable filter elements.

Important information

If you have any concerns about the power supply you are recommended to consult a qualified electrician.

If you have any concerns about the floor load you are recommended to consult a qualified structural engineer.

What you get

Technical Specification

Packaged in two 51cmx61cmx63cm transport boxes
Assembled pool depth 61cm
Assembled pool diameter 162cm
Empty Weight 39kg
Full weight 669kg
Floor load 572kg/sq m
Capacity 636 litres
Operating temperature range 27-40 degrees
Pool is approx 5ft in diameter

Box 1	Box 2
8 X Panels 8 X Uprights 2 X Insulating Foam 1 X Pool Cover	1 X Heater 1 X Main/Base Liner 8 X Foam Cushions
Separate
2x Tap Connectors Electrical Contact Breaker 2 X Replaceable Filter Sets Water Treatment Chemicals	Submersible Pump Stool, Thermometer 2x Hoses Disposable Liner (optional)

Assembly instructions (condensed version - You will receive comprehensive instructions with your pool)
1. Site must be level and clean. It is essential to cover the floor with a plastic sheet to protect from the unlikely event of spills or leaks. If the pool is going onto a hard floor we advise putting an old duvet or some blankets under it to add comfort.
2. The motor unit houses the pump, controller and heater. Position this unit within reach of a standard household plug socket, not an extension lead. DO NOT PLUG IN AND SWITCH ON until other assembly procedures have been completed AND THE POOL FILLED WITH WATER
3. Take a brown upright, one with the locking device, and slide it onto the side of a panel. The popper and locking device should be at the top. If the panel doesn't slide easily, a little application of furniture polish spray or washing up liquid will make it easier. Slot all 7 “complete” panels in place making sure the 4 uprights with locking devices are alternated with uprights that have no locking device.
4. Fit the remaining “half” panel into the uprights with the grey extensions. The panel will rest on the extensions.
5. Fit the foam cushions onto all 8 sides. Place the floor pad on the floor inside the pool.
6. Position the liner inside the pool, making sure you line it up so the pipes are under the half panel, then popper in place. Now line up the heater against the half panel and connect the liner to the heater. If you have Vaseline, or something similar, it is worth putting this on the fittings to ensure you get a tighter hold. Make sure both rubber washers are fitted in the right liner fitting and left heater fitting.
7. If you are using a disposable liner, install the base liner first; it may be white or blue, popper it onto the uprights. The inlet and outlet fittings on the blue disposable liner match up to the holes and similar fittings on the heater. It may take two people to stretch the disposable liner onto the pool. It is much easier if the liner is warm. Leaving it in a room with the heating on for a couple of hours to warm it up, away from the source of heat is a good way to make the liner more elastic.
8. Start filling the pool. You can fill the pool with hot or cold water but bear in mind that if you’re filling it with cold it will take a 12-18 hours to heat. Fill to 8-9 inches (20-32cms) above the inlet/outlet holes. When water level rises to the outlet and inlet, check that the screw fittings are maintaining a watertight connection Fit the water filter according to separate instructions
9. Plug into the power supply and switch on. The unit will set itself to the pre-programmed temperature setting of 37 degrees Centigrade. The display will change to the actual temperature of the water and as the temperature rises the display will change. Warning: always make sure your hands are dry before turning on electrical appliances.
10. Add 20 mls of the chemical to the pool before getting in. Add one tablet to the pool on each day of use. This will give you seven days of moderate use, before you need to empty, clean and refill the pool.
11. You have been supplied with a cover with black straps and an additional insulating foam. The insulating foam looks exactly the same as the floor pad but is found folded with the cover. Float the foam on the water, this will help maintain the temperature and reduce condensation. Fit the lockable cover over the pool and secure it using the locking devices.
12. Fill the pool with water and fit the water filter according to instruction
13.PLUG IN TO THE POWER SUPPLY AND SWITCH ON the unit will set itself to the pre-programmed temperature setting of 37degrees C. The display will change to the actual temperature of the water and as the temperature rises the display will change WARNING: Always make sure your hands are dry before turning on electrical appliances.
14. Always secure the lockable safety cover when the pool is not in use
15. To empty the pool connect hose to pump placing the other end of the hose in a sink or bath. Place the pump in the pool and switch on WARNING: Always make sure your hands are dry before turning on electrical appliances.